Primary Monitored Entrapment Protection: The presence of primary entrapment protection is required for all modes and features beyond basic constant-pressure-to-close performance. Primary entrapment protection devices are monitored continuously to insure safe operation of the door and limit door operator functionality should an obstruction be detected or in the event of device failure. LiftMaster Monitored Entrapment Protection devices, CPS-U, CPS-UN4 and CPS-EI, are designed to work in conjunction with LiftMaster commercial door operators to provide enhanced door safety and a broad range of modes and features to end users. Either monitored photo-sensor or monitored 4-wire sensing edge (in conjunction with the CPS-EI Edge Interface) protection may be selected, but one must be detected by the LiftMaster Logic 4.0 or Medium-Duty Logic circuit board in order to unlock full functionality.

LiftMaster Model MT

liftmasterModelMTMedium Duty Trolley Operator for Standard Lift Sectional Doors   Model MT is a Medium-Duty Logic trolley operator for standard lift sectional doors. It features a high-starting torque motor, a compact design, quick-gliding rail spacers and a quick-mount swivel header bracket. MEDIUM-DUTY LOGIC TECHNOLOGY

Added Value:

  • UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board
  • Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes.
  • 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
  • Programmable C2 or B2 wiring options (B2 requires CPS-U, CPS-UN4, or CPS-EI)
  • Integrated Timer-to-Close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-U, CPS-UN4, or CPS-EI)
  • Integrated 90-second maximum run timer
  • UL325-2010 Monitored Entrapment Capability
  • Monitored protection against transient overvoltage conditions
  • 3-button control station included

STANDARD FEATURESMotor: Powerful 1/2 HP, single phase motor with instant reverse and internal automatic reset thermal overload. Removable without affecting limit switch settings.

Auxiliary Reversal System: Designed to protect the door and door operator from damage; if a closing door strikes an obstruction, the Auxiliary Reversal System will detect the slip of the clutch and reverse the door to the full open position. This system is not a substitute for a safety sensing device such as a photo cell or reversing edge.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close. Momentary contact to close (B2 wiring) can be easily set, but requires the presence of either CPS-U, CPS-UN4, or CPS-EI safety devices. The operator is pre-wired to accept a sensing device, photoelectric control, radio controls and most types of access control equipment.

Rail Assembly: High strength dual L-rail track with exclusive nylon quiet gliding chain guides on rail spacers for quiet, smooth operation. Includes quick-mount header bracket which provides fast, swing-up installation.

Operator/Motor Control: Solid-state Medium-Duty circuit board.

Control Circuit: 24V NEC Class 2.

Drive Reduction: First stage heavy-duty 4L V-belt; second and third stages #48 chain; output on trolley #48 chain.

Emergency Disconnect: Spring-loaded disconnect for emergency manual operation.

Push Button Station: 3-button station for OPEN/CLOSE/STOP functions is standard for all operators. Controls with 1, 2 and 3 buttons are available.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with baked-on powder coat finish, all reduction sprockets drilled and pinned to shafts.

Bearings: Heavy-duty, oil filled bearings.

Radio Receiver: 315MHz radio receiver is integral to the Medium-Duty logic board. Accepts up to 20 Security+® remote controls and unlimited DIP switch remote controls.

Friction Clutch: Adjustable friction clutch helps protect against damage to the door and operator should the door meet an obstruction. Works in conjunction with the Auxiliary Reversal System.

Warranty: 2-year warranty.

 

CONTROL ACCESSORIES AND OPTIONS:

Ancillary Entrapment Protection: (optional) LiftMaster Retro-Reflective Commercial Protector System® photo sensors, 2-wire non-monitored sensing edges and pneumatic sensing edges are considered secondary entrapment protection and may be used to supplement primary entrapment protction or basic constant-pressure-to-close.

Solenoid Brake: Solenoid actuated brake prevents coasting. Order operator BMT. Standard on 3/4 HP and higher.

Auto-Reconnect Trolley Assembly: Spring-loaded trolley features nylon inserts for quiet operation and auto-reconnect feature eliminating the need to manually reattach the door arm to the trolley after emergency disconnect.

Radio Control: Universal transmitters and receivers are available to signal the operator to open and/or close.

Key Switch: Designed to restrict operation of door to authorized personnel only. Various types available.

Interlock Switch: Prevents accidental operation of the door by interrupting the control circuit.

 

 


Liftmaster Model T

 liftmasterModelT

Industrial-Duty Trolley Operator for Standard Lift Sectional Doors

  • Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
  • Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
  • Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U, CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
  • Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

  • Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
  • All high-voltage connections have been removed from the board for safety and ease of service
  • Diagnostic LEDs speed installation and troubleshooting
  • Motor direction jumper lets you change motor direction by simply moving a jumper

Available Plug-in Options for Logic 4.0 (L4)Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices.  Features both normally open and closed contacts that actuate in conjunction with limit switches.

TLS1CARD: Provides seven field-selectable modifications, including six door traffic control options. Combines with Logic 4.0′s standard Timer-to-Close feature to offer timed, sequenced activation of warning lights, sounders, and other devices (sold separately) that can be operated via dry contact closure.

CPS3 or CPS3-N4 Option: Enables the addition of a second set of photo-eyes.

Mechanical Reversing Contactor Circuit (M): (115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit with 40VA transformer) Industrial linear contactor provides significantly longer control runs than conventional contactors.

STANDARD FEATURESMotor: Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase. Removable without affecting limit switch settings.

Drive Reduction: First-stage heavy-duty 5L V-belt; second-stage #41 chain; output on trolley #48 chain on 1/3 and 1/2 HP; #41 chain on 3/4 and 1 HP.

Emergency Disconnect: Spring-loaded for emergency manual operation.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-U, CPS-UN4, or CPS-EI safety edge interface. Operators are pre-wired to accept a sensing edge, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Ball bearings on output shaft; heavy-duty, oil-filled bushings on reduction shafts.

Brake: Solenoid-actuated brake is standard on 3/4 and 1 HP units to prevent coasting of door. Optional on 1/3 and 1/2 HP units.

Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

Quick-Mount Header Bracket: For fast, swing-up mounting.

Rail Assembly: High-strength dual L-rail track with nylon quiet-gliding chain guides on rail spacers for quiet, smooth operation.

Warranty: 2-year warranty.

 

 


LiftMaster Model GT

 liftmasterModelGT

Heavy Industrial-Duty Trolley Operator 

Applications: Model GT is a heavy industrial-duty trolley operator for standard lift sectional doors. It features a continuous-duty high-starting torque motor, quiet-gliding rail spacers, a quick-mount swivel header bracket and a removable hinged electrical box cover. LOGIC 4.0 TECHNOLOGY (L4)

Added Value

  • Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
  • Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
  • Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U, CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
  • Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

  • Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
  • All high-voltage connections have been removed from the board for safety and ease of service
  • Diagnostic LEDs speed installation and troubleshooting
  • Motor direction jumper lets you change motor direction by simply moving a jumper

Available Plug-in Options for Logic 4.0 (L4)

Auxiliary Contact:  Used to operate security, warning, heating or other 5V to 240V devices.  Features both normally open and closed contacts that actuate in conjunction with limit switches.

TLS1CARD: Provides seven field-selectable modifications, including six door traffic control options. Combines with Logic 4.0′s standard Timer-to-Close feature to offer timed, sequenced activation of warning lights, sounders, and other devices (sold separately) that can be operated via dry contact closure.

CPS3 or CPS3-N4 Option: Enables the addition of a second set of photo-eyes.

Mechanical Reversing Contactor Circuit (M):  (115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit with 40VA transformer) Industrial linear contactor provides significantly longer control runs than conventional contactors.

STANDARD FEATURESMotor:  Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/2, 3/4, 1 and 1 1/2 HP; single- or three-phase. Removable without affecting limit switch settings.

Drive Reduction: 10:1 first stage using heavy-duty gears running in oil bath; cast iron housing; #41 chain second stage; #41 chain on trolley.

Emergency Disconnect: Spring-loaded for emergency manual operation.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-U, CPS-UN4, or CPS-EI safety edge interface. The operator is pre-wired to accept a sensing device, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Sealed roller bearings in gear reducer. Flange-mount industrial ball bearings on drive shaft.

Brake: Solenoid-actuated brake is standard.

Clutch: Heavy duty torque limiter helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

Quick-Mount Header Bracket: For fast, swing-up mounting.

Rail Assembly: High-strength dual L-rail track with nylon quiet-gliding chain guides on rail spacers for quiet, smooth operation.

Warranty: 2-year warranty.

Ancillary Entrapment Protection: (optional) LiftMaster Retro-Reflective Commercial Protector System® photo sensors, 2-wire non-monitored sensing edges and pneumatic sensing edges are considered secondary entrapment protection and may be used to supplement primary entrapment protction or basic constant-pressure-to-close.

 

 


LiftMaster Model MH

liftmasterModelMHMedium-Duty Hoist Operator   Model MH is a Medium-Duty Logic hoist operator. It features an adjustable friction clutch, a standard solenoid brake, a high-starting torque motor, a compact design and an emergency chain hoist with an electric interlock. MEDIUM-DUTY LOGIC TECHNOLOGY

Added Value

  • UL325-2010 compliant Medium-Duty Logic programmable integrated circuit board
  • Built-in 3-channel, 315MHz radio receiver accepts up to 20 Chamberlain® Security+® or unlimited DIP switch remotes.
  • 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
  • Programmable C2 or B2 wiring options (B2 requires CPS-U, CPS-UN4, or CPS-EI)
  • Integrated Timer-to-Close (TTC) allows programming from 5 to 60 seconds in 5-second increments. Allows for timed automatic door closure after the door reaches the full open position (Requires monitored safety devices, with CPS-U, CPS-UN4, or CPS-EI)
  • Integrated 90-second maximum run timer
  • UL325-2010 Monitored Entrapment Capability
  • Monitored protection against transient overvoltage conditions
  • 3-button control station included

STANDARD FEATURES

Motor: Powerful 1/2 HP, 115V single phase motor with instant reverse and internal automatic reset thermal overload. Removable without affecting limit switch settings.

Operator/Motor Control: Solid-state Medium-Duty circuit board.

Control Circuit: 24V NEC Class 2.

Emergency Manual Operation: Model MH provides easy emergency manual operation using a floor level disconnect and an electrically interlocked chain hoist mechanism.

Brake: Heavy-duty solenoid actuated brake standard.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop with constant contact to close. Momentary contact to close (B2 wiring) can be easily set, but requires the presence of either CPS-U, CPS-UN4, or CPS-EI safety devices. The operator is pre-wired to accept a sensing device, photoelectric control, radio controls and most types of access control equipment.

Drive Reduction: First stage heavy-duty 4L V-belt; second and third stages #48 chain.

Bearings: Heavy-duty oil-filled bearings.

Push Button Station: 3-button station for OPEN/CLOSE/STOP functions is standard for all operators. Controls with 1, 2 and 3 buttons are available.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with baked-on powder coat finish, all reduction sprockets drilled and pinned to shafts.

Radio Receiver: 315MHz radio receiver is integral to the Medium-Duty logic board. Accepts up to 20 Security+® remote controls and unlimited DIP switch remote controls.

Friction Clutch: Adjustable friction clutch helps protect against damage to the door and operator should the door meet an obstruction.

Warranty: 2-year warranty.

 

CONTROL ACCESSORIES AND OPTIONS

Ancillary Entrapment Protection: (optional) LiftMaster Retro-Reflective Commercial Protector System® photo sensors, 2-wire non-monitored sensing edges and pneumatic sensing edges are considered secondary entrapment protection and may be used to supplement primary entrapment protction or basic constant-pressure-to-close.

Radio Control: Universal transmitters and receivers are available to signal the operator to open and/or close.

Rolling Door Interlock Switch: Interlock switch disables the operator control circuit when a manual door lock is engaged preventing damage to the door and operator.

Weathertight Control Devices: A variety of weathertight control devices are available including 3-button control stations, key control stations and digital keypads.

 

 


LiftMaster Model H Industrial-Duty Hoist Operator

LMindustrialHoist

Model H is an industrial-duty hoist operator. It features a continuous-duty high-starting torque motor, a universal-mount frame design, industrial ball bearings on the output shaft and an emergency chain hoist with an electric interlock. LOGIC 4.0 TECHNOLOGY (L4)

Added Value

  • Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation
  • Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes
  • Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface
  • Thermal motor overload can be easily reset from the 3-button floor level control station

Reliability & Programming Simplicity

  • Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators
  • All high-voltage connections have been removed from the board for safety and ease of service
  • Diagnostic LEDs speed installation and troubleshooting
  • Motor direction jumper lets you change motor direction by simply moving a jumper

Available Plug-in Options for Logic 4.0 (L4)

Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices.  Features both normally open and closed contacts that actuate in conjunction with limit switches.

TLS1CARD: Provides seven field-selectable modifications, including six door traffic control options. Combines with Logic 4.0′s standard Timer-to-Close feature to offer timed, sequenced activation of warning lights, sounders, and other devices (sold separately) that can be operated via dry contact closure.

CPS3 or CPS3-N4 Option: Enables the addition of a second set of photo-eyes.

Mechanical Reversing Contactor Circuit (M): (115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit with 40VA transformer) Industrial linear contactor provides significantly longer control runs than conventional contactors.

 

STANDARD FEATURES

Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection.  Available in 1/3, 1/2, 3/4 and 1 HP; single- or three-phase. Removable without affecting limit switch settings.

Drive Reduction: First-stage heavy-duty 5L V-belt; second and third stages #48 chain; #50 drive chain.

Emergency Disconnect: Easy emergency manual operation using an electrically interlocked floor level disconnect and hoist mechanism.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-U, CPS-UN4, or CPS-EI safety edge interface. The operator is pre-wired to accept a sensing device, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Industrial ball bearings on a 1″ output shaft; heavy-duty oil-filled iron bearings on reduction shafts.

Friction Clutch: Adjustable, helps protect against major damage to door and operator should the door meet an obstruction.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 2-button station for OPEN/CLOSE functions is standard with D or D1 wiring.  3-button station is standard with B2 or C2 wiring.

PosiLock® Mechanical Brake System: Self-locking mechanical reduction system that functions as a holding brake.

Warranty: 2-year warranty.

 

 


LiftMaster Model GH Heavy Industrial-Duty Gear-Reduced Hoist Operator

LMmodelGHhoist

Model GH is a heavy industrial-duty gear-reduced hoist operator. It features a removable hinged electrical box cover and is easily field-converted in seconds for a left or right-handed drive and hoist. LOGIC 4.0 TECHNOLOGY (L4)

Added Value

Built-in 3-channel, 315MHz radio receiver accepts up to 23 Security+® or unlimited DIP switch remotes. 3-button remotes can be programmed for OPEN/CLOSE/STOP operation. Maintenance Alert System™ establishes a routine maintenance schedule based on the number of cycles or calendar date. Includes self-diagnostic system that allows you to troubleshoot up to eight different error codes. Timer-to-Close allows programming in 1-sec or 15-sec increments and permits timed automatic door closure after the door reaches the full open position; requires monitored photo sensors, either CPS-U or CPS-UN4, or a 4-wire edge, using the CPS-EI edge interface. Thermal motor overload can be easily reset from the 3-button floor level control station.

Reliability & Programming Simplicity Switchless motor eliminates stuck start switch and motor malfunctions on single-phase operators. All high-voltage connections have been removed from the board for safety and ease of service. Diagnostic LEDs speed installation and troubleshooting. Motor direction jumper lets you change motor direction by simply moving a jumper.

Available Plug-in Options for Logic 4.0 (L4)

Auxiliary Contact: Used to operate security, warning, heating or other 5V to 240V devices. Features both normally open and closed contacts that actuate in conjunction with limit switches.

TLS1CARD: Provides seven field-selectable modifications, including six door traffic control options. Combines with Logic 4.0′s standard Timer-to-Close feature to offer timed, sequenced activation of warning lights, sounders, and other devices (sold separately) that can be operated via dry contact closure.

CPS3 or CPS3-N4 Option: Enables the addition of a second set of photo-eyes.

Mechanical Reversing Contactor Circuit (M): (115V, 208/230V, 460V, 575V, 24V NEC Class 2 Circuit with 40VA transformer) Industrial linear contactor provides significantly longer control runs than conventional contactors.

STANDARD FEATURES Motor: Continuous-duty high-starting torque motor with instant reverse and overload protection. Available in 1/2 to 5 HP; single- or three-phase. Removable without affecting limit switch settings.

Auxiliary Chain Hoist: Reduced drive chain hoist with electrically interlocked floor level disconnect for manual operation. Hoist wheel is easily moved to right- or left-hand side of unit, eliminating the need to order left- or right-hand mounting.

Drive Reduction: 45:1 using heavy-duty gears running in oil bath. Cast iron housing. Special “all-climate” synthetic gear oil for greater low-temperature performance.

Emergency Disconnect: Spring-loaded for emergency manual operation.

Wiring Type: All operators are factory preset to C2 wiring providing momentary contact to open and stop, with constant contact to close; D1 and E2 wiring are also available. Momentary contact to close (B2 wiring), T, TS, and FSTS wiring can be activated with the use of CPS-U, CPS-UN4, or CPS-EI safety edge interface. The operator is pre-wired to accept a sensing device, photoelectric sensors, radio controls and most types of access control equipment.

External Radio Control Terminal: Quick, convenient connections for retrofitting or adding radio controls on logic or mechanical operators.

Bearings: Sealed roller bearings in gear reducer.

Brake: Solenoid-actuated brake is standard on 3/4 and 1 HP units to prevent coasting of door. Optional on 1/2 HP units.

Construction: NEMA 1 type electrical box, heavy-duty 11-gauge steel frame with durable powdercoat finish, all reduction sprockets drilled and pinned to shafts.

Push Button Station: 3-button station comes standard and has OPEN/CLOSE/STOP functionality.

Warranty: 2-year warranty.

 

 


RSL12V Slige Gate Operator

rsl12v

The RSL12V is our most advanced residential and light commercial pad mounted slide gate operator. It features a powerful DC motor with soft start/stop operation for quiet and reliable performance, and is rated for gates up to 800 lbs. and 25 ft. in length and cycling up to 120 times per day. In addition to a long list of safety and convenience features, the RSL12V can be distinguished by an innovative control board that offers:

EverCharge® Power Management System: Leading the industry with only 8mA power draw when idle including an on-board radio receiver, this system delivers power when needed most for operating the gate while conserving power at all other times, resulting in more cycles when needed for battery backup or optional solar power.

Exceptional Standby Power: Ten seconds after the gate closes, the system switches off non essential ancillary devices to conserve power. This is critical in the event AC power is lost as the battery backup system will remain operational for days or weeks depending on the daily cycle rate and power draw of accessories connected to the 12V accessory power output.

True Power Management System: Our system will not only recover batteries quicker when discharged, it also manages the low power threshold and will not run the batteries beyond the point of failure ensuring they are ready for the next time they are needed.

 

Standard Features

  • Heavy-duty 12VDC motor with soft start/stop operation
  • On-board radio receiver – holds up to 50 remotes
  • Emergency access compliant – selectable auto open feature
  • External manual disconnect
  • Surge/spike protection
  • Inherent obstruction sensing
  • External obstruction sensing inputs
  • Electronic brake
  • Timer to close
  • UV stabilized cover
  • Quantity 1) 7AH battery standard
  • 3-year warranty

Optional Features

  • Solar ready
  • 33Ah battery backup
  • Heater model available
  • MSWIRE12GA6C is required for dual gate operation

Click here to view the Solar Gate Access System Daily Cycle Chart for the RSL12V.  The solar version of this gate operator qualifies for a 30% tax credit.   The US Federal Government is offering financial incentives to homeowners for the use of solar powered systems at their home. Homeowners are able to apply for a Federal Tax credit equal to 30% off the installed cost of their LiftMaster Solar Powered Gate Operator System.

What is Covered: This solar system Tax Credit applies to the total installed cost of the solar gate opener system. This includes the related solar panel, opener, access control device, remote controls, obstruction detection device(s), etc.

What is Not Covered: The cost of the gate itself, or work required to place the physical gate into proper working order (leveling the gate, replacing hinges, etc.)

Qualifications:

  • The installation of a RSL12V Solar Gate System can qualify for a 30% tax credit on the installed system cost
  • Effective for tax years beginning after December 31, 2008
  • You will need to use The Federal Tax Credit form 5695, Residential Energy Efficiency Property Credit
  • You will need to provide a copy of the “Manufacturer’s Certification for Credit”
  • The dwelling must be located in the United States and be used as a residence by the taxpayer
  • This offer is only available in the United States

 

 


LiftMaster SL3000UL™

SL30000UL

The SL3000UL™ models of slide gate operators are the first choice for heavy-traffic applications and high-demand customers, including large development and management companies, prestigious residential gated communities, and custom home builders. The Security+ 2.0™ technology used exclusively in LiftMaster® remote controls virtually eliminates interference and provides up to double the range of standard remotes so you don’t have to wait at the gate to access your property. Featuring the highest quality components and backed by years of proven reliability, each unit is carefully inspected and mechanically tested to provide unsurpassed performance. Unique engineering innovations ensure than any SL3000UL  model will meet the needs of almost every type of high-traffic gated entrance. All backed by the safety and reliability of the most advanced control board in the industry.

  • 120V AC power
  • 24V DC board
  • Built-in model 850LM Security+ 2.0™ Receiver
  • Highly efficient, extremely quiet
  • Surge/lightning protection
  • Alarm reset button
  • Plug-in loop detectors
  • Reversing sensor
  • Limit switch design
  • Modular OmniControl™ Board
  • Wormgear reducer
  • Manual disconnect
  • Weatherproof high-density polyethylene cover
  • Gold zinc-plated chassis eliminates corrosion
  • High-speed precision limit switches
  • Solid steel, machined pulley
  • #41 chain
  • 7-year warranty for residential applications; 5-year warranty for commercial applications

The SL3000UL gate operator is available in the following models:

  • SL3000UL: standard model
  • SL3000ULDC: equipped with battery backup
  • SL3000ULDM: dual motor for heavier traffic and higher temperatures
  • SL3000ULE: capable of manual backdrive for emergency access
  • SL3000UL1HP: heavy-duty, 1 horsepower model for heavier gates

 

 


LiftMaster® SL585

SL585

The LiftMaster® SL585 is a durable heavy-duty gear-driven operator for use on heavy gates and high-cycle applications such as gated communities and industrial locations. The powerful design supports gate lengths up to 70 feet and gate weights up to 1,600 pounds. A strong powder-coated galvanized steel chassis, all-weather gearbox, as well as a weather-resistant, lockable cover ensure years of rugged and reliable performance. This model is ideal for heavy commercial and industrial installations and is UL325-compliant.

  • Built-in radio receiver
  • Universal footprint
  • Larger control box
  • Integrated 3-button control station
  • Large accessory tray
  • External manual disconnect
  • External reset button
  • Inherent obstruction sensing
  • External obstruction sensing
  • Advanced dual gate operation
  • Sequenced access management
  • Digital logic control
  • LED indicators
  • Warning device
  • Loop detector inputs
  • Timer to close
  • Maximum run timer
  • Emergency stop button
  • Maglock control
  • Control inputs
  • Mechanical braking
  • Limit settings
  • Surge & spike protection
  • Hinged access cover
  • 2-year warranty

 

 


LiftMaster® SL575

SL575

The LiftMaster® SL575 is a reliable continuous-duty operator for use on heavy-gate applications in commercial and light industrial locations. This resilient operator offers many standard features such as dual gate operation, sequenced access management, diagnostic LEDs, and more. The SL575 supports gate lengths up to 50 feet and gate weights up to 1,800 pounds, making it ideal for commercial and light industrial installations.

  • Built-in 312HM radio receiver
  • Universal footprint
  • Larger control box
  • Integrated 3-button control station
  • Large accessory tray
  • External manual disconnect
  • External reset button
  • Self-locking drive
  • Inherent obstruction sensing
  • External obstruction sensing
  • Advanced dual gate operation
  • Sequenced access management
  • Digital logic control
  • LED indicators
  • Warning device
  • Loop detector inputs
  • Timer to close
  • Maximum run timer
  • Emergency stop button
  • Maglock control
  • Control inputs
  • Mechanical braking
  • Limit settings
  • Surge & spike protection
  • Hinged access cover
  • 2-year warranty

 

 


CSW200UL8 Commercial Swing Gate Operator

CSW200UL8

The CSW200UL models of swing gate operators are the first choice for heavy-traffic applications such as large gated communities, residential developments, commercial complexes, and private estates. The CSW200UL models of swing gate operators are the first choice for heavy-traffic applications such as large gated communities, residential developments, commercial complexes, and private estates. Unlike other systems, the CSW gate operators are designed with a “non-scissor action” swing arm to greatly reduce the risk of injury. And all models include the safety and reliability of our OmniControl™ board, the most advanced control board in the industry. The Security+ 2.0™ technology used exclusively in LiftMaster® remote controls virtually eliminates interference and provides up to double the range of standard remotes so you don’t have to wait at the gate to access your property. Featuring the highest quality components and backed by years of proven dependability, each unit is carefully inspected and mechanically tested to provide unsurpassed reliability. Unique engineering innovations in each model also ensure that there’s a CSW to meet practically every swing gate application.

  • 120V AC power
  • 24V DC board
  • Built-in model 850LM Security+ 2.0™ Receiver
  • Highly efficient, extremely quiet
  • Surge/lightning protection
  • Alarm reset button
  • Plug-in loop detectors
  • Reversing sensor
  • Limit switch design
  • Soft stop
  • Modular OmniControl™ Board
  • Wormgear reducer
  • Emergency release
  • Weatherproof high-density polyethylene cover
  • Gold zinc-plated chassis eliminates corrosion
  • High-speed precision limit switches
  • Solid steel, machined pulley
  • #41 chain
  • 7-year warranty for residential applications; 5-year warranty for commercial applications

The CSW200UL gate operator is available in the following models:

  • CSW200UL: standard model with a polyethylene cover
  • CSW200ULST: standard model with a stainless steel cover
  • CSW200ULDM: dual motor for heavier traffic and higher temperatures
  • CSW200UL1HP: heavy-duty, 1 horsepower model for heavier gates

 

 


LiftMaster® Elite Series® CSW24V

CSW24V

The LiftMaster® Elite Series® model CSW24V is engineered for a million cycles in high-cycle, heavy-duty applications. A Battery Backup System provides uninterrupted access when the power is out, and Security+ 2.0™ technology virtually eliminates radio interference. It also features integrated MyQ® technology and the industry’s only standard wireless dual gate communication system. The CSW24V is rated for gates 18 ft. long or 1,200 lbs.   Battery Backup System provides uninterrupted access when the power is out Provides up to 7 days or 100 cycles on battery backup. Also powers safety and ancillary devices.

Provides 2x the range of standard remote controls: Our patented Security+ 2.0™ Technology provides two times the range of standard remote controls and virtually eliminates radio interference. An on-board radio receiver is included with the CSW24V. It holds up to 50 remotes and is compatible with HomeLink® version 4 and higher.

Wireless dual gate communication prevents driveway scars and expensive wiring: The on-board radio receiver provides a single remote control solution for gates and additional access points. It also features the industry’s only standard wireless dual gate communication system that saves installation time and cost and eliminates unsightly scars from cutting driveways to run conduit for primary/secondary communication wiring.

Standard Features:

  • Power Management System
    • Supplies power when needed to operate the gate and conserves power when not in use
    • Provides exceptional standby time and cycles on battery backup
    • 7 days of standby time or 100 cycles on battery backup
  • Fire department compliant: selectable settings allow gate to auto-open upon loss of AC power or battery depletion
  • Advanced traffic management control includes Quick-close and Anti-tailgating functions
  • Bi-part delay: choose from Standard Operation or Synchronized Close
  • Simple-to-set electronic limit system maintains accurate gate position throughout gate travel
  • High-density, UV-resistant polycarbonate two-piece cover for excellent heat and corrosion resistance
  • Programmable auxiliary relays
  • Plug-in loop detectors
  • External obstruction sensing; complies with UL325 safety codes
  • 5-year commercial warranty; 7-year residential warranty

Specifications:

  • 24VDC continuous-duty motor with soft start/stop
  • Operator duty rating: continuous
  • Power: 110V or 220V Single Phase
  • Surge/spike protection
  • Gate travel speed: 90-degree opening in 13-15 seconds
  • Constructed with 1/4″ gold zinc-plated steel for rust prevention
  • Weight: 206 lbs.

Optional Features:

  • Photo eyes and reversing edges
  • Plug-in loop detectors
  • Solar package
  • 33AH battery

Click here to view the Solar Gate Access System Daily Cycle Chart for the CSW24V. The solar version of this gate operator qualifies for a 30% tax credit. The US Federal Government is offering financial incentives to homeowners for the use of solar powered systems at their home. Homeowners are able to apply for a Federal Tax credit equal to30% off the installed cost of their LiftMaster Solar Powered Gate Operator System. What is Covered: This solar system Tax Credit applies to the total installed cost of the solar gate opener system. This includes the related solar panel, opener, access control device, remote controls, obstruction detection device(s), etc. What is Not Covered: The cost of the gate itself, or work required to place the physical gate into proper working order (leveling the gate, replacing hinges, etc.)

Qualifications:

  • The installation of a CSW24V Solar Gate System can qualify for a 30% tax credit on the installed system cost
  • Effective for tax years beginning after December 31, 2008
  • You will need to use The Federal Tax Credit form 5695, Residential Energy Efficiency Property Credit
  • You will need to provide a copy of the “Manufacturer’s Certification for Credit”
  • The dwelling must be located in the United States and be used as a residence by the taxpayer
  • This offer is only available in the United States

 

 


 

 

LiftMaster RSW12V

RSW12V

The RSW12V is our most advanced residential and light commercial pad mounted swing gate operator. It features a powerful DC motor with soft start/stop operation for quiet and reliable performance, and is rated for gates up to 600 lbs. or 16ft in length and cycling up to 250 times per day. It also has a built-in battery backup system.

nbsp;

In addition to a long list of safety and convenience features, the RSW12V can be distinguished by an innovative control board that offers:


EverCharge® Power Management System

Leading the Industry with only 8mA power draw when idle including an on-board radio receiver, this system delivers power when needed most for operating the gate while conserving power at all other times, resulting in more cycles when needed for battery backup or optional solar power.


Exceptional Standby Power
Ten seconds after the gate closes, the system switches off non essential ancillary devices to conserve power. This is critical in the event AC power is lost as the battery backup system will remain operational for days or weeks depending on the daily cycle rate and power draw of accessories connected to the 12V accessory power output.

True Power Management System
Our system will not only recover batteries quicker when discharged, it also manages the low power threshold and will not run the batteries beyond the point of failure ensuring they are ready for the next time they are needed.

Standard Features

  • Heavy Duty 12VDC motor with soft start/stop operation
  • On-board radio receiver – holds up to 50 remotes
  • Emergency access compliant – selectable auto open feature
  • Surge/spike protection
  • Inherent obstruction sensing
  • External obstruction sensing inputs
  • Electronic brake
  • Timer to close
  • Bi-part delay
  • UV stabilized cover
  • Quantity 1) 7AH battery standard
  • 3-year warranty

Optional Features

  • Solar ready
  • 33AH battery
  • Heater model available
  • MSWIRE12GA6C is required for dual gate operation

 

Click here to view the Solar Gate Access System Daily Cycle Chart

The solar version of this gate operator qualifies for a 30% tax credit

 

The US Federal Government is offering financial incentives to homeowners for the use of solar powered systems at their home. Homeowners are able to apply for a Federal Tax credit equal to30% off the installed cost of their LiftMaster Solar Powered Gate Operator System.

What is Covered: This solar system Tax Credit applies to the total installed cost of the solar gate opener system. This includes the related solar panel, opener, access control device, remote controls, obstruction detection device(s), etc.

What is Not Covered: The cost of the gate itself, or work required to place the physical gate into proper working order (leveling the gate, replacing hinges, etc.)

Qualifications:

  • The installation of a RSW12V Solar Gate System can qualify for a 30% tax credit on the installed system cost
  • Effective for tax years beginning after December 31, 2008
  • You will need to use The Federal Tax Credit form 5695, Residential Energy Efficiency Property Credit
  • You will need to provide a copy of the “Manufacturer’s Certification for Credit”
  • The dwelling must be located in the United States and be used as a residence by the taxpayer
  • This offer is only available in the United States